Lee FACTORY CRIMP DIE .375 H&H Magnum

» Main Menu » ● SEARCH by BRAND NAME » LEE » Die, FACTORY CRIMP DIE, Rifle » 90850

| My Account | My Shopping Cart | Proceed to Checkout |

Languages

Product Search

Manufacturers

Informatie

● QUESTIONS & ANSWERS

● SHIPPING & ORDERING

● CONDITIONS of USE

Overige Info

● WET WAPENS & MUNITIE

● PRIVACY POLICY

● CONTACT US

Lee FACTORY CRIMP DIE .375 H&H Magnum
[90850]

27.50 Euro

Product may vary slightly from image representation

Description

Factory ammunition is often more accurate and better able to withstand rough handling because the bullet is firmly crimped in place.
A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move.
This higher start pressure insures a more uniform pressure curve and less velocity variation.
Even powder selection is less critical.

The LEE Factory Crimp Die crimps the bullet in place more firmly than any other tool.
It is impossible to buckle the case as with a regular Roll Crimp Die.
Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered.
LEE tests demonstrate that even bullets which have no cannelure will shoot more accurately if crimped in place with the Lee Factory Crimp Die.

A firm crimp is essential for dependable and accurate ammunition.
It eliminates the problems of poor ignition of slow burning reloading powders.

Instructions

The Lee Factory Crimp Die does not seat the bullet. The bullet should be seated with your regular bullet seating die.
Be sure that your bullet seating die is adjusted out far enough so the crimp shoulder is free of the case mouth. Seat to the desired depth.
If the bullet has a crimp groove it is usually best to seat the bullet so most of the groove is inside the case mouth.

● Screw the Lee Factory Crimp Die in to touch the shell holder plus 1/2 turn more. Adjust in for a heavier crimp.
It is usually best to start with too little crimp as you can readjust and crimp again to suit your needs.
When the four plits in the collet are closed maximum crimp has been achieved. Do not try for more as the die will be damaged and the crimp excessive.
If you are using a Lee Press be certain to give the lever a firm push at the end of the stroke to close the collet and apply crimp. ( 25 lbs. minimum )

● Bullets do not need a crimp groove as the Lee Factory Crimp Die will form one while crimping.
However it requires a harder push on the press lever to form the crimp.

● Finger tighten the lock ring.
This locks to both the die and press and it will never move.

● When removing the die always loosen by the lock ring.
This insures the lock ring will maintain its setting for future use.

● Trim length is not critical.
However be certain that your cases are no longer than specification as a case excessively long will pinch the bullet in the end of your gun's chamber and cause dangerous pressures.
Cases trimmed excessively short cannot be crimped.

........ShoppingCart........

1 x	Crosman Part Number AS2250-005, Transfer Tube
1 x	Fluna Tec Easy Clean TFT and Optic Foam Cleaner Spray Can of 100 ml
1 x	Frankford Arsenal PRIMER POCKET SWAGER
1 x	Funfair HART Short Stem ASSORTMENT COLOR set of 10
1 x	H&N Match Green 4.50mm Airgun Pellets tin of 500
1 x	Hornady FULL LENGTH 2-DIE SET .338 Winchester Magnum
1 x	Hornady FULL LENGTH 2-DIE SET 7mm Weatherby Magnum
1 x	Hornady FULL LENGTH 2-DIE SET 8x57, 8x57JS, 8x57JRS Mauser
1 x	Hornady FULL LENGTH 3-DIE SET .444 Marlin
1 x	Hornady Match Grade Bushing .22 caliber, 0.243
1 x	Hornady UNIVERSAL SHELLHOLDER 13
1 x	Lee CASE LENGTH GAUGE .220 Swift
1 x	Lee PACESETTER 3-DIE SET .270 Winchester Short Magnum
1 x	Lee Part Number SE2024, EZ X Expander Decapper, .308 caliber
1 x	Lyman Bullet Mould Rifle 38-55 caliber FLAT NOSE 264 grain
1 x	Lyman GAS CHECKS .284 caliber, 7mm box of 1000 - NO LONGER AVAILABLE
1 x	Lyman GAS CHECKS .35 caliber box of 1000
1 x	Lyman RIFLE 2 DIE SET .30-06 Springfield
1 x	Mag-Lite - Mini MagLite - 2AA - Accessory Pack
1 x	Mag-Lite - Mini MagLite - 2AA - Holster - Nylon - colour Camo
1 x	Outers GUN OIL content 60 ml.
1 x	PARACORD BRACELET with Whistle
1 x	Plano ALL WEATHER Extra Large Pistol Accessory Case
1 x	RCBS Ammomaster 2 Single Stage Reloading Press
1 x	RCBS Bullet Mould Revolver 38, 357 caliber SEMI WADCUTTER 150 grain
1 x	RCBS Pistol Drop Tube, Part Number 88734
1 x	WORTH - SPLIT RING - # 1 - content 15
1 x	Walkers ELITE Shooting Glasses AMBER
1 x	Walkers ELITE Shooting Glasses VERMILLION
1 x	Walther MTL 300 Flashlight
1 x	Weihrauch Part Number 2058A, Safety Lever
1 x	Weihrauch Part Number 9154, Trigger
1 x	Weihrauch Part Number 9245, Forearm Screw Cup
1 x	Weihrauch Piston Seal for Air Rifle model HW55

102,443.65 Euro

Tell a Friend

New Products

Ballistol Silencer Cleaner 500ml
19.50 Euro

All prices are including VAT. All prices are excluding shipping.
To be of better service to you target-master makes use of cookies.

E-mail: contact form

K.v.K. Noord: 01089355.
Licence for Weapons trade: GR 20050217.

Copyright © 2005 - 2024 Target-Master. All rights reserved.