Lee BOTTLE NECK PISTOL FACTORY CRIMP DIE .30 Luger, 7.65mm Luger, 7.65mm Para

» Main Menu » ● RELOADING, Tools and Equipment »
RELOADING DIES, Die Set »
RELOADING DIES, Pistol and Revolver » .30 LUGER, 7.65mm LUGER, 7.65mm PARA » 90175

| My Account | My Shopping Cart | Proceed to Checkout |

Languages

Product Search

Manufacturers

Informatie

● QUESTIONS & ANSWERS

● SHIPPING & ORDERING

● CONDITIONS of USE

Overige Info

● WET WAPENS & MUNITIE

● PRIVACY POLICY

● CONTACT US

Lee FACTORY CRIMP DIE .30 Luger, 7.65mm Luger, 7.65mm Para
[90175]

37.50 Euro

Lee FACTORY CRIMP DIE .30 Luger, 7.65mm Luger, 7.65mm Para

Product may vary slightly from image representation

Description

Factory ammunition is often more accurate and better able to withstand rough handling because the bullet is firmly crimped in place.
A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move.
This higher start pressure insures a more uniform pressure curve and less velocity variation.
Even powder selection is less critical.

A carbide sizer in the Carbide Factory Crimp Die sizes the cartridge while it is being crimped so every round will positively chamber freely with factory like dependability.
The adjusting screw quickly and easily sets the desired amount of crimp.
It is impossible to buckle the case as with a conventional Bullet Seating Die.
Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered.

For revolver rounds a Roll Crimp is used.
A Taper Crimp is applied to auto-loader rounds.
The crimper cannot be misadjusted to make a case mouth too small to properly head-space.

A firm crimp is essential for dependable and accurate ammunition.
It eliminates the problems of poor ignition of slow burning reloading powders.

Instructions

The Lee Factory Crimp Die does not seat the bullet. The bullet should be seated with your regular bullet seating die.
If the bullet has a crimp groove it is usually best to seat the bullet so most of the groove is inside the case mouth.

● Screw the Lee Carbide Factory Crimp Die until it just touches the shell holder and back out the adjusting screw. With the loaded round in the die turn the adjusting screw in until you can feel it just touch the case mouth. Then move the cartridge out of the die slightly and screw the adjusting screw in ½ turn for a light crimp and one full turn for a heavy crimp. You can adjust for even greater crimp and never have to worry about buckling the case as with conventional crimpers.
It is usually best to start with a light crimp as you can readjust and crimp again to suit your needs.

● The case is sized as it enters the die and again as it is pulled out of the die. This assures you every case will freely chamber in any standard gun.
Do not expect the carbide sizer to touch every case. It is a fail safe tool for the occasional bad round that could ruin your day.

● Bullets do not need a crimp groove as the Lee Factory Crimp Die will form one while crimping.
However it requires a harder push on the press lever to form the crimp.

● Finger tighten the lock ring.
This locks to both the die and press and it will never move.

● When removing the die always loosen by the lock ring.
This insures the lock ring will maintain its setting for future use.

● Trim length is not critical.
However be certain that your cases are no longer than specification as a case excessively long will pinch the bullet in the end of your gun's chamber and cause dangerous pressures.
Cases trimmed excessively short cannot be crimped.

You might also like...

Lee CARBIDE 3-DIE SET .40 Smith & Wesson, 10mm Auto

........ShoppingCart........

1 x	A-Zoom SNAP-CAPS 6mm Remington Safety Training Round package of 2
1 x	Birchwood Casey SHOOT-N-C Self-Adhesive Targets 15 Centimeter Targets
1 x	Caldwell ROCK JUNIOR Shooting Rest
1 x	Combat Zone SG1 Safety Glasses
1 x	Crosman Part Number 151-020, Hand Grip, Left side
1 x	Crosman Part Number 2260-002, Filler Rod Assembly
1 x	Crosman SILICONE CHAMBER OIL
1 x	Crosman TRIGGER SHOE Blue
1 x	Edelmann 3305 KNSA Paper Targets KK Karabijn 12 meter 20x22 content 250
1 x	Excite Plinking 5.50mm Airgun Pellets tin of 250
1 x	Frankford Arsenal REPLACEMENT COLLET SET for BULLET PULLER
1 x	GSG Airsoft Battery Charger 7.2 to 12 Volt
1 x	Gamo TS-250 AIRGUN Mounts for 1 inch Scope HIGH 1 piece
1 x	H&N Baracuda 18 5.50mm Airgun Pellets tin of 200
1 x	H&N Slug HP II 6.35mm .249 Airgun Pellets 1.81 gram, 28 grain tin of 120
1 x	Harris 1A2-L Bipod Leg Friction Lock Model height 22 to 32 centimeter
1 x	Harris S-L SWIVEL Bipod Leg Friction Lock Model height 22 to 32 centimeter
1 x	Hornady Lock-N-Load MODIFIED CASE, .224 Valkyrie
1 x	Hornady Lock-N-Load MODIFIED CASE, .338 Lapua Magnum
1 x	Intellect TWIN TYPE Softair Battery 8.4 Volt 1600 mAh
1 x	Lee BULLET LUBE & SIZING KIT caliber .401
1 x	Lee LIQUID ALOX BULLET LUBRICANT
1 x	Lyman ACCU TOUCH 2000 ELECTRONIC RELOADING SCALE
1 x	Lyman DEBURRING TOOL EXTRA LARGE caliber .17 to .60
1 x	Lyman PRIMER POCKET UNIFORMER Small Rifle and Small Pistol
1 x	Lyman ROTARY CASE and MEDIA SEPARATOR
1 x	Lyman TWIN TUMBLER Case Tumbler content 175, 350 pieces .38 special brass
1 x	OUTERS - Barrel Cleaner - BLACK POWDER BORE CLEANER - content 60 ml.
1 x	Parts Drawing Walther 1250 Dominator
1 x	RCBS Lube-A-Matic Top Punch 465
1 x	RWS Super Field 5.51mm Airgun Pellets tin of 500
1 x	Remington REM OIL WIPES 15x20 centimeter content 12 pieces
1 x	Shooters Ridge Rockmount Pivot Bipod Height 22 to 33 centimeter
1 x	Weatherproof Storm Matches, box of 25
1 x	Weihrauch SILENCER 16mm Air Rifle HW80, HW85, HW90, HW95 4.50mm - 5.50mm

101,512.15 Euro

Tell a Friend

New Products

Ballistol Silencer Cleaner 500ml
19.50 Euro

All prices are including VAT. All prices are excluding shipping.
To be of better service to you target-master makes use of cookies.

E-mail: contact form

K.v.K. Noord: 01089355.
Licence for Weapons trade: GR 20050217.

Copyright © 2005 - 2024 Target-Master. All rights reserved.